                        ============================
                         R E L E A S E    N O T E S
                        ============================

                QLogic QCS command line interface utility
                   for Linux (Redhat 5, 6 & 7, SuSE 10 & 11)

                Copyright (c) 2015 QLogic Corporation
                              All rights reserved.
                                May 20, 2015

Version 17.0.14 (May 21, 2015)
-----------------------------------
Fixes
===================
1. Problem:      (Cont75094)
         Add iSCSI iSNS support for Linux
   Cause
         Not supported in Linux so far.
   Change:
         Updated to add/remove iSNS server and manage static target
         binding with bnx2i interfaces
   Impact:
         iSNS Server Management

2. Problem:      (Cont77148)
         Virtual Port (NPIV) help in QCScli is not well written
   Cause
         The command usage/syntax is not mentioned clearly.
   Change:
          Rewritten properly with example 
   Impact:
          Documentation(Readme.txt)
                       

Version 17.0.13 (May 05, 2015)
-----------------------------------
Matched with the GUI version.

Version 17.0.12 (Mar 18, 2015)
-----------------------------------
Fixes
===================
1. Problem:      (Cont78361)
         QCSCli should not allow configuration of 2 personalities 
         on PF#2 and PF#3
   Cause
         Incorrect Error String returned.NDIS mode not handled in CLI
   Change:
         Updated returned type and String and Enabled check for NDIS type
   Impact:
         NPAR1.5 Configuration


2. Problem:      (Cont78362)
         Able to disable Ndis on PF#0 but cannot re-enable after
   Cause         
         Incorrect Error String returned.NDIS mode not handled in CLI
   Change:
         Updated returned type and String and Enabled check for NDIS type
   Impact:
         NPAR1.5 Configuration



Version 17.0.11 (Mar 17, 2015)
-----------------------------------
Fixes
===================
1. Problem:      (Cont78331)
         Seeing Segmentation fault while issuing "list devcon" command when  two Linux hosts are Connected.
   Cause:
         iSCSI target removal logic was causing segfault.
   Change:
         Removed the iSCSI target removal logic.
   Impact:
         QCScli 


2. Problem:      (Cont78361)
         QCSCli - NPAR1.5:  QCS should not allow configuration of 2 personalities 
         on PF#2 and PF#3
   Cause
         Validation is not updated for NPAR1.5 devicecs
   Change:
         Updated to validate NPAR1.5 device separately.
   Impact:
         NPAR1.5 Configuration


3. Problem:      (Cont78362)
         QCSCli - NPAR1.5 - Able to disable Ndis on PF#0 but cannot re-enable after
   Cause
         Improper handling for NPAR personalities
   Change:
         Updated to handle NPAR REs Config properly.
   Impact:
         NPAR Configuration


Version 17.0.10 (Feb 24, 2015)
-----------------------------------
Fixes
===================
1. Problem:      (Cont77820)
         Adapter Configuration showing Single Function for UFP mode
   Cause
         QCS Cli does not support UFP mode
   Change:
         Added support for UFP mode
   Impact:
         NPAR Configuration

2. Problem:      (Cont75279)
         FCoE Config Resources does not work
   Cause
         FCoE Resource reservation not supported
   Change:
         Added support for FCoE Resource reservation 
   Impact:
         command cfg resource


Version 17.0.9 (Feb 12, 2015)
-----------------------------------
1. Problem:      (Cont77820)
         QCS - Adapter Configuration tab showing Single Function for UFP mode
   Cause
         QCS not checking ignoring UFP mode and setting default to SF
   Change:
         Updated to check the UFP mode and change the flag to Multi Function
   Impact:
         NPAR Configuration


Version 17.0.8 (Feb 05, 2015)
-----------------------------------
Fixes
===================
1. Problem:      (Cont77866)
         QCS[GUI and CLI] should configure NPAR based on device and OEM.
   Cause
         QCS do not distnguish between cards and simply 
         configure NPAR1.0 on all the cards.
   Change:
         Updated to check the device ID and configure correct NPAR version.
   Impact:
         NPAR Configuration

		 
Version 17.0.7 (Jan 20, 2015)
-----------------------------------
Matched with the GUI version.


Version 17.0.6 (Jan 13, 2015)
-----------------------------------
Matched with the GUI version.


Version 17.0.5 (Jan 9, 2015)
-----------------------------------
Initial QCS CLI release.


Fixes
=================
N/A - initial release

